Showing posts with label SOP. Show all posts
Showing posts with label SOP. Show all posts

Monday, September 19, 2016

SOP ON REPROCESSING

1. OBJECTIVE

To describe the procedure for reprocessing of intermediate or API, which does not confirm to the standards or specifications.

Wednesday, September 7, 2016

SOP on Rework

1.0            OBJECTIVE

1.1  To define the standard operating procedure for the rework of Intermediate/API.

2.0            RESPONSIBILITY

2.1            Head Quality Control

2.2            Head Quality Assurance

2.3            Head Production

3.0            PROCEDURE
3.1            Definition of rework
3.1.1     Subjecting an intermediate or API that does not conform to  standard or specifications to one or more processing steps that are different from the established manufacturing process to obtain the acceptable quality intermediate or API.

3.2     Whenever a product is found out of specification or non conform, depending upon the nature of failure, a discussion is held between QA, Production, QC and R&D to determine the following:
 3.2.1       Reason for failure and investigation there off.
 3.2.2    Whether the batch is to be reprocessed or reworked to bring it up to the specification.
3.2.3 Whether stability study will be required?
3.2.4 Whether any specific controls to be exercised during rework in case it is to be reworked.

3.3       Based on the outcome of this discussion if rework is recommended then following procedure is adopted.
3.4    Based on the area of non-compliance, production Incharge determines reworking program or method of non conforming batch/material in consultation with quality assurance, quality control and if needed be with R & D.
3.5            It is also determined whether the situation is likely to occur again.
3.6         If it is found to be one –off situation proper technical study is undertaken for the efficacy of the rework protocol in achieving the rework objectives.
3.7          This protocol is adopted only if its technical soundness is fully established.
3.8     If however it is found that the non conforming situation is such that it may occur again, in that case the rework protocol is suitably validated before adoption.
3.9       The rework protocol is documented along with any control measure and records that are to be made to ensure compliance to the protocol.
3.10       A draft manufacturing record shall be prepared by production on the basis of recommendation of QA, QC and R&D.
3.11       Batch number shall be assigned as per Batch numbering SOP
3.12       All reworked batches shall be suitably identified so as to make it explicitly clear about their status as a reworked batch.
3.13  After the batch is reworked, the batch is analysed for it compliance with specifications.
3.14    A final test report is issued to production from QC after compliance of product with specification.
3.15    Comparison of impurity profile of each reworked batch against batches manufactured by the established process to be done.
3.16   Where routinely analytical method are inadequate to characterise the reworked batch, additional method should be used from approved accredited laboratory.
3.17       Adequate documents are prepared and archived with the BMR to describe the reason, steps taken and result.
3.18       The accelerated stability studies of reworked batches will be undertaken if the method used in unique and has not been studied for stability earlier.
3.19       The reworked batches may be released for commercial purposes if the quality of such batches is similar to the normal production batches.


4.0            ABBREVIATION
 4.1            NIL

5.0            ANNEXURES
 5.1            NIL

6.0            REFERENCE
6.1            ICH Q7 14.30,14.31,14.32


ALSO READ

Saturday, August 13, 2016

SOP on cleaning on hose pipe

Below is the standard operating procedure to clean the Hose pipes. In some manufacturing companies hose pipe is also known as flexible pipe.

Monday, August 8, 2016

Procedure on Good Recording Practices

OBJECTIVE
To lay down a procedure for Good Recording Practices.

RESPONSIBILITY
Personnel - All departments.
Heads – All Departments

PROCEDURE
  • Personnel shall make on line entries in the documents.
  • The entries made by the operating personnel shall be checked and signed by the    supervising       personnel.
  • No entry shall be over written.
  • If anything is wrong do not over write it.

Friday, July 29, 2016

Gowning Procedure

1.0              OBJECTIVE

1.1              To outline the procedure for personal cleanliness for entry into high risk zones.


2.0              PROCEDURE

3.1              Enter into the change room.

3.2        Remove he accessories like mobile phones, wrist watches, rings, wrist bands, ornaments or jewellery.

3.3            Before entering, personnel shall either cover their street shoes with disposable covers or wear footwear that are earmarked for this purpose.

3.4              Move to the other side of the crossover bench.

3.5              Wash hands thoroughly.

3.6              Wear head gear to cover head.

3.7              Wear the mask and cover the beard.

3.8             Wear the gown. 

3.9              Take one or two drop of hand sanitizer on palm and rub it to evaporate it.

3.10          Enter the high risk zone.

3.11     Person shall remove their gowns and keep them in the change room before going outside the area.

3.12       Remove all the gowns whenever going out of the high risk zone even for a short period.

3.13          Follow entire procedure all over again whenever you re-enter the high risk zone.

3.14          Use neck chain for the spectacles or safety eye glasses.  

3.15          All the gowns shall be collected in basket and sent to the laundry at the end of the day.


4.0              ABBREVIATIONS

4.1              NIL

5.0              ANNEXURES

5.1              NIL

6.0              REFERENCE

6.1              NIL

            Detail gowning procedure and board are available if users/readers require the same. If there are any query/questions or suggestions related to the article, readers are requested to mail their query at anshuyadav.icgian@gmail.com. 


AUTHOR :ANSHU YADAV
anshuyadav.icgian@gmail.com





Thursday, July 28, 2016

HAND WASHING TECHNIQUE

Hand washing is an important step which is to be followed before entering into the manufacturing and processing area of any food and Pharmaceutical company. Hand washing facility is generally inspected during any regulatory inspection or customer audit.


In many of the manufacturing unit the supervisors/workers or operators are unable to understand the procedure in english, therefore it shall be written in their local language.

Below is the procedure given for hand washing. Target audience are supervisors/workers and operators of the manufacturing unit in food and pharma companies

      1.     Wet the hands with water.  अपने  हाथो  को  पानी  से  गीला करें 
2.      Take some liquid soap on the palm.   तरल साबुन को अपनी हथेली पर ले 
3. Make lather of the soap by rubbing palm together. दोनों हथेलियों को आपस में रगड़ कर झाग बनायें 
4.     Rub your hands as below step wise:  अपने हाथो को इस प्रकार रगड़िए
             4.1       Both the palms together / दोनों हथेलिओं को आपस में रगड़े
             4.2    Rub back of each hand with the other palm  /  एक हथेली से दुसरे हाथ के ऊपर के हिस्से को  रगड़िए 
4.3        Interlace finger and rub together as below.  / दोनों हाथों की उंगलिओं को नीचे बनी  आकृति  की तरह मिला कर आपस में रगड़ें  
4.4        Curl the back of the finger into one palm then the other.  / एक हाथ की उंगलिओं को मोड़ कर दुसरे हाथ की हथेली को रगड़ें
4.5     Hold thumb and rotate with both hands / एक हाथ के अंगूठे को दुसरे हाथ से पकड़ें और घुमाए
5.     Wash the hands with plenty of water. / फिर पानी से अपनी हाथ को अच्छी तरह से धोएं
6.     Dry the hand with the help of Dryer./ ड्रायर की मदद से अपनी हाथों को सुखाएं 
7.     The above process will be done every time when the workers are entering in the process area./
ऊपर दिया हुआ तरीका एम्प्लोयी को जब भी वह प्रोसेस एरिया में जाये फॉलो करना है I

As per 21 CFR 110.37 (e)

Hand washing facilities shall be adequate and convenient and be furnished with running water at a suitable temperature.

Compliance may be accomplished by providing ;

a) Hand washing facilities and where appropriate hand sanitizing facilities at each location in the plant where good sanitary practices require employees to wash and/or sanitize their hand.

b) effective hand cleaning and sanitizing preparations.

c) Sanitary towel service or suitable drying devices.

d) Devices or fixtures, such as water control valves, so designed and constructed to protect against re-contamination of clean, sanitized hands.

e) Readily understandable signs directing employees handling unprotected food, unprotected food packaging materials, of food contact surfaces to wash and where appropriate, sanitize their hands before they start work, after each absence from post of duty, and when their hands may have become soiled or contaminated. These signs may be posted in the processing room(s) and in all other areas where employees may handle such food, material, surfaces. 

f) Refuse receptacles that are constructed and maintained in a manner that protects against contamination of food.

g) Rubbish and offal disposal. Rubbish and any offal shall be so conveyed, stored and disposed of as to minimize the development of odor, minimize the protection for the waste becoming an attractant and harborage or breeding place for pests, and protect against contamination of food, food contact surfaces, water supply and ground surfaces.

If there are any query/question or suggestions related to the article readers are requested to mail there query at anshuyadav.icgian@gmail.com.


AUTHOR : ANSHU YADAV
anshuyadav.icgian@gmail.com.